SLZB-MR3
What it is: A network multi-radio coordinator from SMLIGHT with two radios: TI CC2674P10 and Silicon Labs EFR32MG24. It runs Zigbee and Thread at the same time, connects via Ethernet with PoE, USB-C or Wi-Fi, and is managed by SLZB-OS.1
Specifications
According to the original vendor product page1, chip parameters according to the chip makers.
Radios
| TI CC2674P10 | Silicon Labs EFR32MG24 | |
|---|---|---|
| Protocols | Zigbee 3.0, Thread (Matter-over-Thread) | Zigbee 3.0, Thread (Matter-over-Thread) |
| Primarily for (SMLIGHT) | Zigbee | Thread |
| Radio firmware | TI Z-Stack (ZNP) | Ember/EZSP |
| TX power | +20 dBm, integrated PA2 | +20 dBm per SMLIGHT, max. +19.5 dBm per Silicon Labs3 |
| Core | Arm Cortex-M33 48 MHz + Cortex-M0 radio controller2 | Arm Cortex-M33 78 MHz3 |
| Flash / RAM | 1 MB / 296 kB2 | up to 1536 kB / up to 256 kB depending on variant3 |
| Sensitivity (802.15.4) | โ105 dBm2 | โ |
| Extras | Secure boot, AES-256, TRNG2 | AI/ML accelerator, Secure Vault3 |
Both radios can run at the same time; Zigbee and Thread should be on different channels.1 SMLIGHT doesn't state the exact EFR32MG24 variant, so flash and RAM are given only as a range.
Control and connectivity
- MCU: ESP32. It controls the whole device and runs SLZB-OS 2.8.7 or later.1
- Ethernet: RJ45, Microchip LAN8720 PHY. USB-C: data and power, CP2102 converter.1
- Wi-Fi and Bluetooth: via an internal PCB antenna.1
- LAN or USB mode is switched in the web UI or with a short button press. USB and Ethernet are optically isolated, so both cables can be connected at once.1
Power and antennas
- PoE IEEE 802.3af (48 V), USB-C 5 V, or both. The power source is detected automatically; there's no switch.1
- Consumption: up to 1.5 W with both radios running.1
- The PoE transformer may whine quietly. According to the vendor that's fine as long as it can't be heard from more than 50 cm away.1
- Antennas: 2ร SMA female, one per radio. Two external 2.4 GHz antennas rotatable in three axes are included; the vendor states "+5 dB" without a dBi unit.1
Build and controls
- ABS case with vent holes. Mounting on a DIN rail (3D bracket models), screws on a wall (kit included) or double-sided tape.1
- 6 service LEDs: 2 for the ESP32, 2 for the CC2674P10 and 2 for the EFR32MG24. The power LED can be turned off.1
- One button for mode switching, reset and other functions.1
- The MR3 page doesn't list dimensions, weight or operating temperature.
Firmware and updates
- Ships pre-flashed. Firmware of both radios and the ESP32 can be updated remotely via the web UI.1
- Roles: Zigbee coordinator or router (depending on the flashed radio firmware), OpenThread Border Router, zHub mode in SLZB-OS.1
- ESP32 Autoboot: the ESP32 can be flashed over USB-C without buttons or an external programmer.1
- Several adapters with one HA: Zigbee2MQTT needs a separate instance per coordinator.1
SLZB-MR3 vs. SLZB-MR3U
The original MR3 page now points to a new page that already shows the SLZB-MR3U.1,4 It has the same radios but a different control section: ESP32-S3 (2ร 240 MHz), WIZnet W5500 Ethernet (10/100 Mb) and an extra USB-A passthrough for another dongle. It lists Thread 1.3 and dimensions of 160 ร 24 ร 28 mm (86 g). Don't carry MR3U parameters over to the MR3 without checking. The original page text also mentions the SLZB-MR1 in places and "PoE 802.5af", which is a typo.
SLZB-06M vs. SLZB-MR3
According to the vendor product pages5,1:
| SLZB-06M | SLZB-MR3 | |
|---|---|---|
| Radios | 1ร Silicon Labs EFR32MG21 | 2ร TI CC2674P10 + Silicon Labs EFR32MG24 |
| Zigbee 3.0 | yes, coordinator or router | yes, coordinator or router |
| Thread | only instead of Zigbee (different firmware) | yes, alongside Zigbee on the second radio |
| TX power | +20 dB | +20 dBm per radio |
| Antennas | 1ร external "+5 dB" | 2ร SMA, external "+5 dB" |
| Control MCU | ESP32 | ESP32 |
| Ethernet / USB | LAN8720 / CP2102, USB-C | LAN8720 / CP2102, USB-C |
| Wi-Fi | yes | yes |
| PoE | IEEE 802.3af | IEEE 802.3af (48 V) |
| Power consumption | not stated | up to 1.5 W |
| LEDs | 4 | 6 (2 per chip) |
| Dimensions | 160 ร 22 ร 24 mm | not stated |
| Operating temperature | +5 to +35 ยฐC | not stated |
| Successor on the SMLIGHT site | SLZB-06MU | SLZB-MR3U |
Synthesis: for a pure Zigbee network the 06M is enough. The MR3 pays off when you want Zigbee and Thread from one PoE device.
How to use it
- A typical MR3 setup (Synthesis based on the product page1 and the6): one radio as the Zigbee coordinator for ZHA or Z2M via the network socket (
tcp://<ip>:6638), the other as an OpenThread Border Router for Thread and Matter. Both from one PoE device. - On dual-radio devices the Z2M/ZHA settings in SLZB-OS appear for each radio separately, and each is configured on its own.6
- The configuration generator in SLZB-OS prints the adapter type and port for Z2M (
configuration.yaml) or ZHA. For the CC2674P10 that's the ZNP family, for the MG24 EZSP/Ember.6,1 - Modes, Zigbee Hub mode, security and migration are covered on the Zigbee page in the SLZB section and in Zigbee coordinator migration.
Security
Vendor recommendations6:
- Web UI login with a strong password.
- Set the socket IP whitelist to the HA or Z2M server.
- In normal operation, disable the web UI while the socket is connected.
- Password-protect the fallback Wi-Fi AP.
Related
Sources
- SLZB-MR3 (SMLIGHT product page) โ โ original SMLIGHT product page (MR3 specifications).
- TI CC2674P10 (Texas Instruments product page) โ โ TI product page for the CC2674P10 chip.
- Silicon Labs EFR32MG24 (Silicon Labs pages) โ โ Silicon Labs on the EFR32MG24 family.
- SLZB-MR3U (new SMLIGHT product page) โ โ new SMLIGHT page, already for the SLZB-MR3U.
- SLZB-06M (SMLIGHT product page) โ โ SLZB-06M product page (comparison).
- SLZB-OS (SMLIGHT Manuals) โ โ SLZB-OS manual (dual-radio setup, socket, security).
Intellihome